Mitsubishi A Series Serial

note this driver is available for manufacturing connect edge version 3 5 2 and later review the following information for setting up and configuring the mitsubishi a series serial driver manufacturing connect edge compatible series compatibility parameter compatible items driver type serial validated devices/series a series models a1s a2n a2a a2u a2as a2ush a3a a2n a1sh a2sh replaces gen 1 driver(s) mitsubishi a2n serial (gen1) docid\ sndnvnuqewbsgbs50uxys mitsubishi a2sh serial (gen1) docid\ dkjvr88rffsauy6xwzamz mitsubishi a2ush serial (gen1) docid\ qi1aqwvignczalimevist to set up and configure this device in manufacturing connect edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in manufacturing connect edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device record the serial communication parameters for the device otherwise, use plc software on your computer to look up these parameters these parameters will be used for setting up the driver in the next step step 2 set up the plc device in manufacturing connect edge devicehub configure the following parameters when you connect a device docid\ rfvijdxz7dbad8mwbisma with this driver update default values to the specific setup of your device parameter value type mitsubishi driver mitsubishi a series serial device file the file of the serial port you are using baud rate select one of the following 1200 2400 4800 9600 19200 38400 57600 115200 230400 460800 921600 data bits select one of the following 5 6 7 8 stop bits select one of the following 1 1 5 2 parity select one of the following even mark none odd space plc type select one of the following a2n a2sh a2ush step 3 configure the list of registers when you add tags docid\ ioanzd2awqnkuppgee3eh to the connected device, refer to the following register table and tag parameters refer to the following additional resources organize device and tag data by using metadata docid\ f b720nivllber44rfyhn tag formula variables docid\ pwd 7p kzjxkt pyawaow register table note the address format in this gen 2 driver is different from the replaced gen 1 drivers for the same device name value types address format min address max address description x bit hhh 0 2047 input relay y bit hhh 0 2047 output relay m bit dddd 0 2047 internal relay b bit hhh 0 1023 link relay f bit dddd 0 1023 annunciator r word ddddd 0 65535 file register w word hhh 0 1023 link register d word dddd 0 1023 data register cv word dddd 0 4095 counter memory tv word ddd 0 255 timer memory tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address count enter the number of register values to read a count higher than 1 will generate an array of values from the address value configured and respective subsequent address values tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to customize nats messages to be published only when the value parameter changes from a previous value to a new one change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on it can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)