Keyence Serial (Gen1)

review the following information for setting up and configuring the keyence serial (gen1) driver manufacturing connect edge compatible series compatibility parameter compatible items driver type serial validated devices/series https //www keyence com sg/products/controls/plc building block type/kv 8000/models/kv l20v/ https //www keyence com sg/products/controls/plc building block type/kv 5000 3000/models/kv 700/ https //www keyence com sg/products/controls/plc building block type/kv 5000 3000/models/kv 1000/ https //www keyence com sg/products/controls/plc building block type/kv 5000 3000/models/kv 3000/ https //www keyence com sg/products/controls/plc building block type/kv 5000 3000/models/kv 5000/ https //www keyence com sg/products/controls/plc building block type/kv 7000/models/kv 7500/ https //www keyence com/products/controls/plc building block type/kv 8000/ to set up and configure this device in manufacturing connect edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in manufacturing connect edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device record the serial communication parameters for the device otherwise, follow the steps below to configure your device note down the following information and refer to it when needed device keyence kv 40dt communication i/f rs232 refer to the following figures launch kv studio software select hmi and plc devices set up the plc step 2 set up the plc device in manufacturing connect edge devicehub configure the following parameters when you docid\ rfvijdxz7dbad8mwbisma with this driver update default values to the specific set up of your device parameter value type keyence driver keyence serial (gen1) communication port local serial connection file path baud rate 115200 data bits 8 parity even, odd, none stop bits 1 step 3 configure the list of registers when you docid\ ioanzd2awqnkuppgee3eh to the connected device, refer to the following register table and tag parameters refer to the following additional resources docid\ f b720nivllber44rfyhn docid\ pwd 7p kzjxkt pyawaow register table name value type address format min address max address description mr bit dddddd 0 399915 internal auxiliary relay lr bit ddddd 0 99915 latch relay cr bit ddddd 0 99915 control relay r bit ddddd 0 99915 relay b bit hhhh 0 32767 link relay t bit bit dddd 9999 counter bit c bit bit ddddddd 0 6553515 data memory bit sm bit vir dddddd 0 999915 temporary data memory bit cm bit bt ddddddd 0 6553515 control memory bit em bit bit ddddddd 0 6553515 data memory fm bit bit ddddddd 0 6553515 file register bit ctc bit bit d 0 7 w bit bit hhhh 0 524287 link register bit vm bit bit ddddddd 0 6553515 vb bit bit hhhh 0 63999 ctc word d 0 7 cth word d 0 3 z word dd 1 12 cs word dddd 0 9999 counter preset cc word dddd 0 9999 counter current ts word dddd 0 99999 timer preset tc word dddd 0 9999 timer current b word word hhh 0 2047 link relay r word word ddd 0 999 relay vb word hhh 0 3999 cr word word ddd 0 999 control relay lr word word ddd 0 999 latch relay mr word word dddd 0 3999 internal auxiliary relay fm word ddddd 0 65535 file register em word ddddd 0 63535 data memory vm word ddddd 0 65535 w word hhhh 0 32767 link register tm word dddd 0 9999 temporary data memory dm word ddddd 0 65535 data memory tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)