Fanuc CNC Ethernet (Gen1)

12 min

Review the following information for setting up and configuring the Fanuc CNC Ethernet (Gen1) driver.

Manufacturing Connect Edge Compatible Series

Compatibility parameter	Compatible items
Driver type	Ethernet
Validated devices/series	Any PLC model that supports FANUC FOCAS

To set up and configure this device in Manufacturing Connect Edge, you will need to do the following:

Step 1: Set up and Configure the PLC Device

Step 2: Set up the PLC Device in Manufacturing Connect Edge DeviceHub

Step 3: Configure the List of Registers

Step 1: Set up and Configure the PLC Device

If the device is configured for Ethernet access, find its network parameters. Otherwise, follow the steps below.

Review the following parameters for the PLC Configuration.

Supported Data Types

Refer to the following supported data types by Fanuc and Manufacturing Connect Edge. Below is for the Fanuc PMC (Programmable Machine Control).

Fanuc Macro variables support the FLOAT data type.

Table 1

Data Type	Size
BYTE	1 byte
WORD	2 bytes

Table 2

Signed Value	Data Type	Size
INT8	SINT	1 byte
INT16	INT	2 bytes
INT32	DINT	4 bytes

Table 3

Unsigned Value	Data Type	Size
UINT8	USINT	1 byte
UINT16	UINT	2 bytes
UINT32	UDINT	4 bytes

The Fanuc PMC System is the interface between the Fanuc CNC and the machine tool. For information on the PMC system, visit the Fanuc Corporation website.

RDPMC Tags

RDPMC tags provide all information about the Address Type, the Address Number to read data from, and Size within the tag itself.

Address types

Example of an RDPMC Tag

Tag	Address Type	Address Number	Size
Rdpmc [9_746_2]	D	746	4 bytes

In the previous example, 9 refers to an address type listed in the image, 746 is the address number to read data from, and 2 means that the data is four bytes long.

Configure Device

Refer to the following configurations if the device doesn't connect right away.

To configure the device:

Note down the following information and refer to it when needed.

Device: Fanuc 0i-F

Communication I/F: Ethernet. Refer to the following figure.

Fanuc CNC Ethernet reference

Press Soft key five times to set up the IP Address.

IP Address set up screen

Press the Soft key Embed Port to set up the network parameters, and then press the Soft key OPRT.

Set up network parameters screen

Press the Soft key Restart to activate the settings.

Activate settings screen [1]

Press the Soft key Execute to activate the settings.

Activate settings screen [2]

Press the Soft key two times to reach this page, and then press the Soft key FOCAS2.

FOCAS2 button reference

Set up the port number, and then press the Soft key OPRT.

Port setup screen

Step 2: Set up the PLC Device in Manufacturing Connect Edge DeviceHub

Configure the following parameters when you Connect a Device with this driver. Update default values to the specific set up of your device.

Parameter	Value
Type	Fanuc Corporation
Driver	Fanuc CNC Ethernet (Gen1)
Network Address	The device address you defined in Step 1
Port	8191

Step 3: Configure the List of Registers

When you Add Tags to the connected device, refer to the following register table and tag parameters.

Refer to the following additional resources:

Register Table

Name	Value Types	Address Format	Min Address	Max Address	Description
G_Bit	bit	DDDDo	0	999977
F_Bit	bit	DDDDo	0	99997
Y_Bit	bit	DDDDo	0	99997
X_Bit	bit	DDDDo	0	99997
A_Bit	bit	DDDDo	0	99997
R_Bit	bit	DDDDDo	0	599997
T_Bit	bit	DDDDo	0	99997
K_Bit	bit	DDDDo	0	99997
C_Bit	bit	DDDDo	0	99997
D_Bit	bit	DDDDo	0	99997
E_Bit	bit	DDDDo	0	99997
G	usint,sint,int,uint,dint,udint	DDDD	0	9999
F	usint,sint,int,uint,dint,udint	DDDD	0	9999
Y	usint,sint,int,uint,dint,udint	DDDD	0	9999
X	usint,sint,int,uint,dint,udint	DDDD	0	9999
A	usint,sint,int,uint,dint,udint	DDDD	0	9999
R	usint,sint,int,uint,dint,udint	DDDD	0	59999
T	usint,sint,int,uint,dint,udint	DDDD	0	9999
K	usint,sint,int,uint,dint,udint	DDDD	0	9999
C	usint,sint,int,uint,dint,udint	DDDD	0	9999
D	usint,sint,int,uint,dint,udint	DDDD	0	9999
E	usint,sint,int,uint,dint,udint	DDDD	0	9999
cnc_absolute	dint	D	1	8
cnc_absolute2	dint	D	1	8
cnc_machine	dint	D	1	8
cnc_relative	dint	D	1	8
cnc_distance	dint	D	1	8
cnc_acts	dint	D	0	0
cnc_acts2	dint	D	1	8
cnc_actf	dint	DDDD	0	0
cnc_rdmacror	float	DDDD	1	9999
cnc_rdtoolrng_number	dint	DDDD	0	9999
cnc_rdtoolrng_life	dint	DDDD	0	9999
cnc_rdtoolrng_count	dint	DDDD	0	9999
cnc_rdparam	sint,int,float	DDDDDDD	0	9999947	Address consist of 2 parts. last 2 numbers are axis.
cnc_rdparam3	sint,int,float	TDDDDDDD	0	19999947	Address consists of 3 parts; last 2 number are axis, T:0 Relative axis, 1 Absolute axis.
cnc_rdalmmsg	custom	D	0	0
cnc_rdalmmsg2	alarm	D	0	0
cnc_rdalminfo	alarmInfo	D	0	19
cnc_statinfo	statinfo	D	0	0
cnc_statinfo2	statinfo	D	0	0
cnc_gettimer_date	date	D	0	0
cnc_gettimer-time	time	D	0	0
cnc_rdtpfsr	dint	TDDDD	0	19999	T 0: Machining Mode, 1: Lathe mode
cnc_rdsvmeter	custom	D	0	0
cnc_rdspmeter_meter	custom	D	0	0
cnc_rdspmeter_speed	custom	D	0	0
cnc_exeprgname	custom	D	0	0
cnc_rdseqnum	custom	D	0	0
cnc_rdblkcount	custom	D	0	0
cnc_rdopnlsgnl	custom	D	0	0
cnc_sysinfo	custom	D	0	0
cnc_sysinfo_ex	custom	D	0	0
cnc_alarm	custom	D	0	0
cnc_alarm2	custom	D	0	0
cnc_rdposition	custom	D	0	0
cnc_rdtofsinfo	custom	D	0	0
cnc_rdtofsinfo2	custom	D	0	0
cnc_tofs_mge	custom	TTTDDDD	0	1029999
cnc_rdparainfo	custom	DDDD	0	9999
cnc_rdparainfo3	custom	DDDD	0	9999
cnc_rdactfixofs	custom	DD	1	48
pmc_rdpmcinfo	custom	DD	0	99
pmc_getdtailerr	custom	D	0	0
pmc-rdalmmsg	custom	DD	1	99
cnc_diagnoss	sint,int,float	DDDDDDD	0	9999947
cnc_diagnosr	sint,int,float	DDDDDDD	0	9999947	Address consist of 2 parts. last 2 numbers are axus,
cnc_rddiaginfo	custom	DDDDD	0	99999
cnc_rdopmsg	custom	D	0	9
cnc_rdopmsg2	custom	D	0	9
cnc_rdopmsg3	custom	D	-1	9
cnc_rdspcss	custom	D	0	0
cnc_rdspeed	custom	D	0	0
cnc_rdspload	custom	DD	0	99
cnc_rdspmaxrpm	custom	DD	0	99
cnc_rdspgear	custom	DD	0	999
cnc_rdgrpid2	custom	DDDDD	0	99999
cnc_rdngrp	custom	D	0	0
cnc_rdntool	custom	DDDDD	0	99999
cnc_rdlife	custom	DDDDD	0	99999
cnc_rdcount	custom	DDDDD	0	99999
cnc_rd1length	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rd2length	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rd1radius	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rd2radius	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_t1info	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_t2info	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_toolnum	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rdtoolgrp	custom	DDDDD	0	99999
cnc_rdtoolgrp	custom	D	0	0
cnc_rdusegrpid	custom	D	0	0
cnc_rdmaxgrp	custom	D	0	0
cnc_rdmaxtool	custom	D	0	0
cnc_rdusetlno	custom	DDDDD	0	99999
cnc_rd1tlifedata	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rd1tlifedat2	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rd2tlifedata	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rdgrpinfo	custom	DDDDD	0	99999
cnc_rdgrpinfo2	custom	DDDDD	0	99999
cnc_rdgrpinfo3	custom	DDDDD	0	99999
cnc_rdgrpinfo4	custom	DDDDD	0	99999
cnc_rdtinfo	custom	D	0	0
cnc_rdtlusegrp	custom	D	0	0
cnc_rdtlgrp	custom	DDDDD	0	99999
cnc_rdtltool	custom	TTTTTDDDDD	0	9999999999	Address consist of 2 parts. first 5 numbers are group number.
cnc_rdexchgtgrp	custom	DDDDD	0	99999
cnc_rdtlgeomsize_ext	custom	DDDDDD	0	199999	Address consist of 2 parts. first 1 numbers are coordinate.
cnc_rdzofs	dint	DDDdd	0	99948	Address consist of 2 parts. first 3 numbers are offset number, second 2 numbers are axis.
cnc_rdzofsinfo	dint	D	0	0
cnc_rdfixofs	dint	Ddd	101	848	Address consist of 2 parts. first 1 numbers are c fixture offset number.
cnc_rdintchk	dint	DDDDd	0	99997	Address consist of 2 parts. first 4 numbers are check data number, second 1 number is type of coordinate.
cnc_rdwkcdshft	dint	DD	1	48
cnc_rdwkcdsfms	dint	DD	1	48
cnc_wksft_rnge	custom	DD	1	48
cnc_dtsvcnclupdn	custom	D	0	0
cnc_dtsvgetdncpg	custom	D	0	0
cnc_rddncfname	custom	D	0	0
cnc_rddsdncfile	custom	D	0	1	0: DATA SERVER, 1: DATA SERVER Host
cnc_dsftpstat	custom	D	0	0
cnc_dsftpcancel	custom	D	0	0
cnc_rdloopgain	custom	D	0	0
cnc_rdcurrent	custom	D	0	0
cnc_rdsrvspeed	custom	D	0	0
cnc_rdnspdl	dint	D	0	0
cnc_rdopmode	custom	D	0	0
cnc_rdposerrs	custom	D	0	0
cnc_loadtorq	short	Ddd	0	147	D 1: Spindle motor, 0: Servo motor, dd: Axis
cnc_rddiag_ext	custom	DDDD	0	9999	DDDD: Specify the pointer to the array of the diagnosis data numbers.
cnc_getpath	dint	D	0	0
cnc_sysconfig	custom	D	0	0	Reads the CNC system configuration information.
cnc_rdmenuswitch	dint	D	0	0
cnc_rdradofs	custom	D	0	0
cnc_rdlenofs	custom	D	0	0
cnc_rdfixcycle	customcustom	D	0	0
cnc_rdcdrotate	custom	D	0	0
cnc_rd3dcdcnv	custom	D	0	0
cnc_rdmirimage	custom	D	0	0
cnc_rdscaling	custom	D	0	0
cnc_rd3dtofs	custom	D	0	0
cnc_rdposofs	custom	D	0	0
cnc_rdaxisdata	custom	Dd	10	59	D: class of data, d: type
cnc_skip	custom	DD	1	48	DD: axis
cnc_srvdelay	custom	DD	1	48	DD: axis
cnc_accdecdly	custom	DD	1	48	DD: axis
cnc_rdmovrlap	custom	DD	1	48	DD: axis
cnc_canmovrlap	custom	DD	1	48	DD: axis
cnc_rdhndintrpt	custom	D	0	1	0: input unit, 1: output unit
cnc_rd3dtooltip	custom	D	0	0
cnc_rd3dpulse	custom	D	0	0
cnc_rd3dmovrlap	custom	D	0	0
cnc_rd3dofschg	dint	D	0	0
cnc_rdunsolicprm	custom	D	0	0
cnc_rdunsolicprm2	custom	D	0	0
cnc_rdunsolicmsg	custom	D	0	0
cnc_rdunsolicmsg2	custom	D	0	0
cnc_modal	custom	DDDD	0	3033	Address consist of 2 parts. First 3 numbers are the type.
cnc_rdgcode	custom	DDDD	0	1032	Address consist of 2 parts. First 3 numbers are the group of G code.
cnc_rdcommand	custom	DD	10	32	Address consist of 2 parts. First number is type. 1: Read all modal data except G code at a time, 2: Read all commanded data at a time, 3: Read all commanded data concerning axis at a time. Second Number is block.
cnc_rdmacro	float	DDDD	0	9999	custom macro variable number
cnc_rdmacror2	float	DDDD	0	9999	custom macro variable number
cnc_wrmacro	float	DDDD	0	9999	custom macro variable number
cnc_wrmacror	float	DDDD	0	9999	custom macro variable number
cnc_wrmacror2	float	DDDD	0	9999	custom macro variable number
pmc_wrcntldata	custom	DDDD	0	9999	group number
pmc_wrcntlgrp	uint	D	0	0	group number
pmc_wrkpm	custom	DDDDD	0	65535	start address
pmc_wrkpm2	custom	DDDDD	0	65535	start address
pmc_wrmsg	custom	0	0	0	start address
pmc_wrpmcparam	custom	0	0	0	start address

Tag Parameters

Name: Select a register name from the drop-down list. The available options depend on the names in the register table.

Value Type: Select a data type from the drop-down list. The available options depend on the register name selected.

Polling Interval: Enter a value in seconds. This determines how often the tag should poll the register for data.

Tag Name: Enter a name for the tag.

Description (Optional): Enter a description for the tag.

Address: Enter a tag address. The value must in the decimal format, within the allowed min/max range. Omit the leading zeros. The device might use the decimal (D), hexadecimal (H), or octal (O) address format. See the Register Table at the bottom of the dialog box. For Bit tags, append the bit address without the bit separator. The lowercase letters in the address format indicate how many digits you should enter in the Bit address.

Path No: Enter the path number.

If you are using 2-path control with independent macros on each path, then entering 1 or 2 should be the correct configuration.

If you are using custom macro common variables (the macros used are the same for each path), then this value should be irrelevant and the default value of 1 can be used.

Count: Enter the number of register values to read. A count higher than 1 will generate an array of values from the address value configured and respective subsequent address values.

Tag Formula: Enter a formula for the tag to process the generated data. Two variables are permitted: value (current tag value) and timestamp (current tag UNIX time in milliseconds). The following math functions are available:

sqrt

power: power(x) performs the operation 10^x.

log: log(x) is the natural logarithm (the logarithm is in base e).

exp: exp(x) performs the operation e^x.

Only Publish on Change of Value: Select the checkbox to only publish NATS messages when the value parameter changes to a new value. Change of Value only applies to boolean, numeric (such as int or float), and simple string data types. It does not apply to complex types, such as JSON or array. Poll-once topics will not be affected by Change of Value settings. These topics will still only see a single message.

Meta Data: Metadata summarizes basic information about data. This feature allows you to define key-value pair data for the device output payload later on. Metadata can then be used to find, use, and reuse particular instances of data.

Note: If you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload. This can cause two key names to be combined into one. For example, configuring the key names a**b and a&&b will cause only one key name to be created (a__b).