ISO Installation on an Industrial PC (IPC)

you can install manufacturing connect edge with a physical gateway from a usb important the data storage visualization technology raid (redundant array of inexpensive disks) is not supported when installing manufacturing connect edge on an industrial pc before you begin usb pre installation checklist review the current release notes format a usb flash drive with at least 8gb of storage space to fat32 download and install software to create a bootable usb drive (for example, balenaetcher if using balenaetcher, you must skip the validation step when creating the bootable flash drive ) load the manufacturing connect edge installer iso file on the usb drive manufacturing connect edge must have an x86 or amd64 device for installation see system requirements docid 3lcvn9ni8yqid3zmadg5 for more information ensure that there is enough space on the desired partition for manufacturing connect edge set the correct system time in the device bios to prevent any license activation issues utc is recommended to ensure that the device boots after a power loss, set the boot mode in the bios to uefi set the boot order to boot from usb in the bios connect a monitor and keyboard to the device connect a mouse to non serial devices for navigating the install gui you have a basic knowledge of bios and selecting bootable media adjust the system clock using the bios prior to installing manufacturing connect edge the 15 day trial period may be rejected and invalidated by the license server if the system clock is not adjusted if this happens, contact your litmus representative adjust the boot mode setting to uefi using the bios prior to installing obtain a valid file in the iso format you can download it from manufacturing connect (mc) > edge management > downloads alternatively, you can obtain an iso file from litmus make sure you have more than 16gb disk space to run 3 x images on a bare metal server to use a physical gateway to install manufacturing connect edge, you will need to do the following step 1 download iso file step 2 create a bootable usb flash drive step 3 install on a device step 4 log in to manufacturing connect edge step 1 download iso file download the manufacturing connect edge iso file from manufacturing connect (mc) > edge management > downloads step 2 create a bootable usb flash drive you will need to create a bootable usb flash drive and then load the iso file onto the flash drive important the boot mode should be uefi if you are using balenaetcher , you must skip the validation step while creating the flash drive otherwise, manufacturing connect edge won't install successfully after preparing the usb drive, choose the instructions that are relevant for the device for which you are installing manufacturing connect edge step 3 install on a device there are two methods to installing manufacturing connect edge on a device install on a device with graphic capability install on a device with no graphic capability (headless installer) select the method relevant for your device these instructions are applicable for vga devices that can render the graphics displayed in the installer notes during the installation, the progress bar may decrease at times due to partitioning the time to complete the installation is based on the size of the hard disk drive large disk drives will cause the installation to take longer to partition the disk and therefore longer to complete setting up the virtual machine install on a device with graphic capability complete these steps to install from a usb flash drive to install on a device with graphic capability insert the usb flash drive (usb installation media) that contains the manufacturing connect edge installer image into the usb port on the gateway device to execute the installer, the gateway device must boot from the usb flash drive perform one of the following start the gateway device reboot the gateway device from the usb flash drive to begin the installation if the gateway device is not booting from the usb drive, bring up a list of boot devices each manufacturer has a specific button which must be pressed immediately after the device has been turned on or rebooted the button is briefly displayed when the device boots after or while the logo is displayed common buttons are f12, the windows key, and f9 refer to your ipc manufacturer for more information after the device initiates the installer, respond to the questions in the terminal user interface (tui) welcome to operating system installer are you installing over serial (for advanced users)? yes/no enter no , and then press enter select install operating system , and then select ok use the arrow keys to navigate to selections select the partition to install, and then select ok the list is device specific typically, the installation location is sda if the device/gateway has embedded mmc (emmc) components, the partition name may be listed as mmcblk instead of sda make sure you select the correct hard drive location verify the os installation location by selecting yes if you select no , you are returned to the beginning of the installation a second verification ensures that you are overwriting the correct device partition during the formatting process select yes to continue formatting the device and installing the operating system the installer indicates its progress, followed by a success message power off the device and remove the usb drive (installation media) reboot the gateway device the terminal window displays the url that must be used to access the device using the web ui note if several urls are displayed, the first one is used for accessing the device through the web ui you can now jump to "step 3 log in to manufacturing connect edge" install on a device with no graphic rendering capabilities (headless installer) complete these steps to install from a serial device to install on a device with no graphic rendering capabilities insert the usb flash drive (usb installation media) that contains the manufacturing connect edge installer image into the usb port on the gateway device to execute the installer, the gateway device must boot from the usb flash drive perform one of the following start the gateway device reboot the gateway device from the usb flash drive to begin the installation if the gateway device is not booting from the usb drive, bring up a list of boot devices each manufacturer has a specific button that must be pressed immediately after the device has been turned on or rebooted the button is briefly displayed when the device boots after or while the logo is displayed common buttons are f12, the windows key, and f9 refer to your ipc manufacturer for more information after the device initiates the installer, respond to the questions in the terminal user interface (tui) welcome to operating system installer are you installing over serial (for advanced users)? yes/no enter yes to continue with a text only interface, and then press enter a list of partitions are displayed this list is specific to the device enter the partition name in this example, sda if the device/gateway has embedded mmc (emmc) components, the partition name may be listed as mmcblk instead of sda make sure you select the correct hard drive location you must type the name of the device if you press enter without typing the name, the installation fails confirm the installation and format partitions, enter yes , and then press enter the installer displays the installation status, followed by a success message remove the usb flash drive reboot the gateway device the terminal window displays the url that must be used to access the device using the web ui typically, the url to use starts with 192 if several urls are displayed, use the first one step 4 log in to manufacturing connect edge see access the manufacturing connect edge web ui docid 9y0 n74s8m5x4gynbfb9u for details on logging in see access the terminal user interface docid\ nv5 vdiqscyc3uktney38 for instructions on how to navigate and log in for the first time