VirtualBox ISO

you can use virtualbox to install manufacturing connect edge using an iso file before you begin prepare your environment for running virtualization by using oracle virtualbox review verified vm versions docid 36xpluiltp2qajsr8lthw and confirm the correct version to download see virtualbox downloads https //www virtualbox org/wiki/downloads refer to virtualbox documentation https //www virtualbox org/wiki/documentation to learn more the virtual machine will run on the same physical network card as the host environment to ensure that the device can communicate with data sources such as plc, dcs or cnc and can be accessed through the web ui, make sure that communication can be established adjust the system clock for the host environment prior to installing manufacturing connect edge utc is recommended the 15 day trial period may be rejected and invalidated by the license server if the system clock is not adjusted if this happens, contact your litmus representative obtain a valid file in the iso format you can download it from manufacturing connect (mc) > edge management > downloads alternatively, you can obtain an iso file from litmus to use virtualbox to install manufacturing connect edge using an iso file, you will need to do the following step 1 create a virtual machine step 2 configure the virtual machine step 3 install the iso file step 4 run manufacturing connect edge on the virtual machine step 5 log in to manufacturing connect edge to jump to a specific section, refer to the table of contents on the right side and click the corresponding step step 1 create a virtual machine you will need to create a virtual machine (vm) that will be used to run manufacturing connect edge to create a virtual machine start the virtualbox application from the oracle vm virtualbox manager window, click new on the toolbar the create virtual machine dialog box appears if needed, toggle guided mode to expert mode the dialog box expands enter a name for the virtual machine in the name field select linux from the type drop down list select other linux (64 bit) from the version drop down list you can select linux 2 6, 3 x, or 4 x (64 bit) move the memory size slider to set the memory size the minimum is 2 gb of (2048 mb) select more memory if the host system permits from the hard disk section, select create a virtual hard disk now click create the create virtual hard disk dialog box appears from the hard disk file type section, select the vmdk (virtual machine disk) from the storage on physical hard disk section, select dynamically allocated move the file size slider to set the file size the minimum value is 16 gb, which enables the vm to run this size provides the resulting vm with about 2 gb of data storage this is enough for a small scale poc without much data storage on the disk if this vm is deployed as a production system or the poc requires more storage for databases, increase the file size beyond 16 gb click create the new vm is deployed it appears on the list in the oracle vm virtualbox manager window step 2 configure the virtual machine after installing the vm, you will need to configure it to configure the virtual machine you created from the oracle vm virtualbox manager window, select the new vm on the left pane, then click settings on the toolbar the settings dialog box appears from the left pane, select system the system pane appears on the right click the motherboard tab from the pointing device drop down list, select ps/2 mouse from the boot order section, highlight the optical option and then click the up arrow to make this option first on the list make sure the optical option is not deselected when moving it click the processor tab move the processor(s) slider to set the cores for the vm to 2 (the recommended minimum) if the host system permits or the vm is a production deployment, more cores should be allocated from the left pane, select storage the storage pane appears on the right from the storage devices section, select the controller from the type drop down list, select ahci if ahci is not available, select, piix4 the piix4 option works, but displays a number of messages throughout the installation from the storage devices section, select the optical drive (currently shown as empty ) from the attributes section, click the optical drive icon and select choose a disk file navigate to the iso file from which you want to install, and then click open the optical drive in the storage devices section displays the name of the iso file you selected from the left pane, select audio the audio pane appears on the right clear the enable audio output check box from the left pane, select network the network pane appears on the right click the adapter 1 tab select the enable network adapter check box from the attached to drop down list, select bridged adapter select the appropriate network card name from the name drop down list select the adapter 2 tab select the enable network adapter check box from the attached to drop down list, select nat from the left pane, select usb the usb pane appears on the right deselect the enable usb controller check box click ok step 3 run the operating system installer you will run the operating system installer that will install manufacturing connect edge notes during the installation, the progress bar may decrease at times due to partitioning the time to complete the installation is based on the size of the hard disk drive large disk drives will cause the installation to take longer to partition the disk and therefore longer to complete setting up the virtual machine to install the iso file from the oracle vm virtualbox manager window, select your vm and click start on the toolbar if prompted, select the iso file you added to the optical device in the storage settings, then click start if the start button does not close the prompt box, click cancel this will not interfere with the installation the terminal user interface (tui) appears if a message appears warning you that the mouse you are using is not supported in tui, ignore it you can navigate the tui using arrow keys and make selections by pressing the enter key during loading, the terminal user interface may display the following warning/error messages these can be ignored after the device initiates, respond to the questions in the tui enter no to continue with the installation using the graphical interface select install operating system , and then select ok select the partition to install, and then select ok the list is device specific typically, the installation location is sda if the device/gateway has embedded mmc (emmc) components, the partition name may be listed as mmcblk instead of sda make sure you select the correct hard drive location select yes to verify the os installation location if you select no , you return to the beginning of the installation select yes to continue formatting the device and installing the operating system the installer indicates its progress followed by a success message after installation, the terminal user interface may display the following warning/error messages these can be ignored select yes to power off the device step 4 run manufacturing connect edge on the virtual machine once the iso file is successfully installed, you can run manufacturing connect edge on the virtual machine to run manufacturing connect edge on the virtual machine you will need to remove the iso file from the optical drive from the oracle vm virtualbox manager window, select your vm on the left pane on the right pane, click the \[optical drive] text in the storage section the selected file turns blue right click the file and deselect the iso file the optical drive shows empty in the system section, select boot order highlight hard disk , click the up arrow to move the hard disk to the top, and then click ok the order should be hard disk, optical, and floppy click start during loading, the terminal user interface may display the following warning/error messages these can be ignored the vm starts up and the terminal window displays the urls to be used to access the edge device through the web ui if several urls are shown, use the first one step 5 log in to manufacturing connect edge see access the manufacturing connect edge web ui docid 9y0 n74s8m5x4gynbfb9u for details on logging in see access the terminal user interface docid\ nv5 vdiqscyc3uktney38 for instructions on how to navigate and log in for the first time troubleshooting if you don't see an option for a 64 bit version and only see a 32 bit version, refer to virtualbox only showing 32 bit and no 64 bit versions docid\ h5abb9q5kfja1fnt4bxrp