AB PLC5 (Gen1.3)

review the following information for setting up and configuring the ab plc5 (gen1 3) driver manufacturing connect edge compatible series compatibility parameter compatible items driver type serial validated devices/series plc5 https //www rockwellautomation com/en us/products/hardware/allen bradley/discontinued products/plc 5 controllers html to set up and configure this device in manufacturing connect edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in manufacturing connect edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device record the serial communication parameters for the device otherwise, follow the steps below note when configuring the settings for the plc, the error detect setting must be set to crc, otherwise a connection with manufacturing connect edge won't be successful refer to the following parameters and reference images when setting up the plc device plc5/40c communication i/f ꓽ rs232 complete the following steps to setup and configure the plc to configure the plc connect the plc to the computer with a serial port 25 pin d shell cable open rslinx classic software click the configure drivers icon then, click add new\ and add the rs 232 df1 devices driver configure the driver with the following parameter values and click ok baud rate 9600 bits per char 8 stop bits 1 parity none error detect crc in the driver settings, click auto configure and confirm you see an auto configuration successful! message ensure these same settings are configured in the plc to establish a connection open rslogix 5 software click comms and select who active go online select the device that you configured and click online in the navigation menu, click channel configuration and select open confirm the serial port settings for channel 0 , which is the rs232 port note down the baud rate, data bits, stop bits, and parity the error detect setting must be set to crc you can use channel 3a to configure the ethernet port, if applicable step 2 set up the plc device in manufacturing connect edge devicehub configure the following parameters when you connect a device docid\ rfvijdxz7dbad8mwbisma with this driver update default values to the specific set up of your device parameter value type allen bradley driver ab plc5 (gen1 3) communication port local serial connection file path data bits 8 baud rate 9600 parity even, odd, none stop bits 1 slot 0 step 3 configure the list of registers when you add tags docid\ ioanzd2awqnkuppgee3eh to the connected device, refer to the following register table and tag parameters refer to the following additional resources device and tag metadata use case docid\ f b720nivllber44rfyhn tag formula variables docid\ pwd 7p kzjxkt pyawaow register table name value type address format min address max address description i bit ddddd 0 25515 input bit o bit ddddd 0 25515 output bit s int ddd 0 255 status file b3 bit ddddd 0 25515 bfn bit fffddddd 10000 25525515 t4 acc int ddd 0 255 timer accumulator (t4) t4 pre int ddd 0 255 tfn acc int fffddd 10000 255255 tfn pre int fffddd 10000 255255 cs acc int ddd 0 255 counter accumulator (cs) cs pre int ddd 0 255 cfn acc int fffddd 10000 255255 dfn pre int fffddd 10000 255255 r6 int ddd 0 255 control file(r6) r6 pos int ddd 0 255 control file pointer position (r6) r6 len int ddd 0 255 rfn int fffddd 0 255255 rfn pos int fffddd 0 255255 rfn len int fffddd 0 255255 n7 int, bit(int) ddddd 0 25515 nfn int, bit(int) fffddddd 10000 25599915 lfn int fffddd 10000 255999 f8 float ddd 0 255 ffn float fffddd 10000 255999 tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)