ABB Totalflow DB2 (Gen1.3)

review the following information for setting up and configuring the abb totalflow (gen1 3) driver manufacturing connect edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series 6000 series fcu https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers 6000 series microflo https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers 6000 xseriesg3 https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers 6000 xseriesg4 https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers please refer to the following devices that are not compatible with this driver irc5 controller https //new\ abb com/products/robotics/controllers/irc5 overview/irc5 as an alternative, you can connect through an opc ua server to set up and configure this device in manufacturing connect edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in manufacturing connect edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, use plc software on your computer to configure the device for ethernet access step 2 set up the plc device in manufacturing connect edge devicehub configure the following parameters when you connect a device docid\ rfvijdxz7dbad8mwbisma with this driver update default values to the specific set up of your device parameter value type abb driver abb totalflow db2 (gen1 3) network address the device address you defined during step 1 network port 9999 step 3 configure the list of registers when you add tags docid\ ioanzd2awqnkuppgee3eh to the connected device, refer to the following register table and tag parameters you can also search for pre defined device tags docid\ mocoh 5sebdz22wwbjsuf for this device refer to the following additional resources device and tag metadata use case docid\ f b720nivllber44rfyhn tag formula variables docid\ pwd 7p kzjxkt pyawaow register table the register table addresses follow the format \<application> \<array> \<register> when entering the address in devicehub, add left padding zeros and remove the period delimiters the list of registers can be found in the totalflow xseries remote controller user's manual https //library e abb com/public/f767e1b1766dfa26c1257b1a005b0e6b/xrc%20manual%20aa pdf name data type address format min address max address bit bit tttfffdddd 0 2552553647 w bit bit tttfffdddddd 0 255255364715 byte byte, sint tttfffdddd 0 2552553647 word word, int, dword, dint, float, double, lword, lint tttfffdddd 0 2552553647 dword dword, dint, float, double, lword, lint tttfffdddd 0 2552553647 string string tttfffdddd 0 2552553647 tag parameters name select a register name from the drop down list available options depend on the names in the register table value type select a data type from the drop down list available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address count enter the number of register values to read a count higher than 1 will generate an array of values from the address value configured and respective subsequent address values tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to publish nats messages only when the value parameter changes to a new one value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics are not affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on it can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)