Mitsubishi Q00-01H Serial (Gen1.3)

review the following information for setting up and configuring the mitsubishi q00 01h serial (gen1 3) driver manufacturing connect edge compatible series compatibility parameter compatible items driver type serial validated devices/series melsec q https //www mitsubishielectric com/fa/products/cnt/plcq/items/index html to set up and configure this device in manufacturing connect edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in manufacturing connect edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device record the serial communication parameters for the device otherwise, follow the steps below refer to the following parameters online simulator yes extend address mode no broadcast command no to configure your device note down the following information and refer to it when needed device mitsubishi q03udcpu and qj7124n communication i/f rs232 refer to the following figure launch gx works2 v1 560 software, and then click online > read from plc from the plc series selection dialog box, select qcpu (q mode) from the plc series drop down list, and then click ok set up communication parameters, and then click connection test right click intelligent function module > new module set up module parameters as shown below click switch setting and set up communication parameters as shown below step 2 set up the plc device in manufacturing connect edge devicehub configure the following parameters when you connect a device docid\ rfvijdxz7dbad8mwbisma with this driver update default values to the specific set up of your device parameter value type mitsubishi driver mitsubishi q00 01h serial (gen1 3) communication port local serial connection file path data bits 8 baud rate 9600 parity even, odd, none stop bits 1 step 3 configure the list of registers when you add tags docid\ ioanzd2awqnkuppgee3eh to the connected device, refer to the following register table and tag parameters refer to the following additional resources device and tag metadata use case docid\ f b720nivllber44rfyhn tag formula variables docid\ pwd 7p kzjxkt pyawaow register table name value type address format min address max address description x bit hhhh 0 8191 input relay y bit hhhh 0 8191 output relay m bit ddddd 0 61439 internal relay l bit ddddd 0 32237 latch relay f bit ddddd 0 32237 annunciator v bit ddddd 0 32237 edge relay b bit hhhh 0 61439 link relay tc bit dddd 0 2047 timer coil ss bit ddddd 0 25471 retentive timer contact sc bit ddddd 0 25471 retentive timer coil cs bit ddddd 0 25471 counter contact cc bit ddddd 0 25471 counter coil sb bit hhh 0 2047 special link relay s bit dddd 0 8191 step relay dx bit hhhh 0 8191 direct input dy bit hhhh 0 8191 direct output ts bit dddd 0 2047 timer contact sm bit dddd 0 2047 w word hhhh 0 12187 link register tn word dddd 0 2047 timer current value sn word dddd 0 2047 retentive timer current value cn word dddd 0 1023 counter current value r word ffddddd 0 32767 file register sw word hhhh 0 2047 special link register z word dd 0 19 index register zr word hhhhh 0 1042341 file register d word ddddddd 0 4212735 data register sd word dddd 0 2047 tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)