Omron-NJ-Ethernet (Gen1.3)

review the following information for setting up and configuring the omron nj ethernet (gen1 3) driver manufacturing connect edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series nj https //www ia omron com/products/category/automation systems/programmable controllers/controller nj series/index html nx1p https //www ia omron com/products/category/automation systems/programmable controllers/controller nx1p/index html when configuring tags for this driver, you must enter the case sensitive register name exactly as it is defined in the plc see the free tags section below to learn more to set up and configure this device in manufacturing connect edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in manufacturing connect edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, follow the steps below to configure your device note down the following information and refer to it as needed device omron nj ethernet communication i/f ethernet refer to the following figure connect the device with a usb cable launch sysmac studio v1 20 1 0 software, select controller > communication setup , and then set up the ip address use a direct connection in usb > usb communication test step 2 set up the plc device in manufacturing connect edge devicehub configure the following parameters when you connect a device docid\ rfvijdxz7dbad8mwbisma with this driver update default values to the specific set up of your device parameter value type omron driver omron nj ethernet nj301 1100 network address the device address you defined during step 1 port 44818 step 3 configure the list of registers when you add tags docid\ ioanzd2awqnkuppgee3eh to the connected device, refer to the following tag parameters and available value types refer to the following additional resources device and tag metadata use case docid\ f b720nivllber44rfyhn tag formula variables docid\ pwd 7p kzjxkt pyawaow free tags this driver doesn't have a list of available register names in the devicehub add tag form to add tags, you must enter the case sensitive register name exactly as it is defined in the plc a connected status for the device won't display until a tag with a correct register name is created and a value is generated (not null/blank) available value types the following value types are available for manufacturing connect edge version 3 11 0 and later bool sint usint byte int uint word dint udint dword real lint ulint lword lreal string time date date and time time of day the following value types are available for manufacturing connect edge version 3 10 0 and earlier bool sint usint byte int uint word dint udint dword real reading dint arrays if you want to read a dint array, you need to write the element number of the array that you want to read in square brackets along with the tag name example if the array name is arraydint and you want to read the third element of the array, the format for the tag name in manufacturing connect edge is arraydint\[2] tag parameters name enter the case sensitive register name exactly as it is defined in the plc value type select a data type from the drop down list polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)